how setup robe stage qube
Moderator: MADRIX Team
how setup robe stage qube
Hi,
I have problem to setup MADRIX.
I have rent for a show at next weekend robe stage qube.
I have enable robe stage cube in options device network and MADRIX have found all panels at the next restart.
My problem: I can't control all pixel of the panel. All pixel at left side of the panel are ok, but at the right side I can only control 9 pixel.
I have install different version of MADRX an tested.
I have more then 5 create a new patch.
I have check the network and ping all robe stage qube and all say ok.
I have no more ideas.
Can anybody help my?
I have problem to setup MADRIX.
I have rent for a show at next weekend robe stage qube.
I have enable robe stage cube in options device network and MADRIX have found all panels at the next restart.
My problem: I can't control all pixel of the panel. All pixel at left side of the panel are ok, but at the right side I can only control 9 pixel.
I have install different version of MADRX an tested.
I have more then 5 create a new patch.
I have check the network and ping all robe stage qube and all say ok.
I have no more ideas.
Can anybody help my?
Re: how setup robe stage qube
Hi dieter,
.
it sounds like you patched !generic RGB fixture instead of Robe StageQube 324.
.
Please check this out.
.
it sounds like you patched !generic RGB fixture instead of Robe StageQube 324.
.
Please check this out.
LEDs are nothing without control
Re: how setup robe stage qube
Hi Wissman,
yes thats is it.
I have changed in my patch and set to ROBE stage qube 324.
Now its running and the show can start.
THX
I have another 2 questions for ROBE stage qube 324.
1:
I'm surprised this Fixture have more than 512 channels.
How can I this control with normaly DMX?
2:
How I can view all channels of one robe stage qube 324?
The build in DMX watcher from MADRIX show only the first 512 channels of the one ROBE StageQube 324. I can't found the rest of the channels from the ROBE robe stage qube 324?
yes thats is it.
I have changed in my patch and set to ROBE stage qube 324.
Now its running and the show can start.
THX
I have another 2 questions for ROBE stage qube 324.
1:
I'm surprised this Fixture have more than 512 channels.
How can I this control with normaly DMX?
2:
How I can view all channels of one robe stage qube 324?
The build in DMX watcher from MADRIX show only the first 512 channels of the one ROBE StageQube 324. I can't found the rest of the channels from the ROBE robe stage qube 324?
Re: how setup robe stage qube
Hi Dieter,
.
fine it is working now for you.
.
Yes the Robe Stage Qubes 324 have 18 by 18 rgb pixel which makes a total amount of 972 channels if it would be controled by DMX512.
.
But the INSTA 2022 and the Robe Stage Qube 324 are controled by a special network protocol which is not DMX512, it is more simmilar to Art-Net or KiNet but not the same.
We are proud to be able to support this protocol.
So it is not possible to control the Stage Qubes with a standard DMX512 control solution of several reason. Do for example the Stage Qubes provide a white balance feature which is handled by the network protocol as well.
Also it is necessery to set up a DHCP server for fixed installations, so the Stage Qubes get always the same IP address based on there MAC address.
For this you have two options, either using a hardware router where you setup the IP´s for the MAC´s or using a software router like TFTP to do this.
.
Regarding the DMX Watcher....
.
Oh oh, it´s a shame, we have to own up while developing the DMX Watcher we haven´t think about the Robe Stage Qubes or the GLP DMX1024 (used by ion tubes)
So we will fetch it up now
.
Ones again thank you very much for your comments and hints!!
.
fine it is working now for you.
.
Yes the Robe Stage Qubes 324 have 18 by 18 rgb pixel which makes a total amount of 972 channels if it would be controled by DMX512.
.
But the INSTA 2022 and the Robe Stage Qube 324 are controled by a special network protocol which is not DMX512, it is more simmilar to Art-Net or KiNet but not the same.
We are proud to be able to support this protocol.
So it is not possible to control the Stage Qubes with a standard DMX512 control solution of several reason. Do for example the Stage Qubes provide a white balance feature which is handled by the network protocol as well.
Also it is necessery to set up a DHCP server for fixed installations, so the Stage Qubes get always the same IP address based on there MAC address.
For this you have two options, either using a hardware router where you setup the IP´s for the MAC´s or using a software router like TFTP to do this.
.
Regarding the DMX Watcher....
.
Oh oh, it´s a shame, we have to own up while developing the DMX Watcher we haven´t think about the Robe Stage Qubes or the GLP DMX1024 (used by ion tubes)
So we will fetch it up now
.
Ones again thank you very much for your comments and hints!!
LEDs are nothing without control
Re: how setup robe stage qube
Sorry for late answer,
I was on tour with some very great bands
Was a great tour, No sleep. Under a lot of stress. But MADRIX running ever and there updates are big, bigger, biggest
M$ system are bad
I love this simple software. Ever have run If I needed.
I was on tour with some very great bands
Was a great tour, No sleep. Under a lot of stress. But MADRIX running ever and there updates are big, bigger, biggest
M$ system are bad
I love this simple software. Ever have run If I needed.
Re: how setup robe stage qube
Thank you so much for this kind words !
LEDs are nothing without control